Happymodel Crux35 ELRS V2 Analog / Crux35 Digital HD 150mm 3.5 Inch 4S Ultralight FPV Racing Drone BNF w/ CADDX Nebula Pro / ANT 1200tvl Camera

Motor

Mode: EX1404
KV options: KV3500
Configu-ration:9N12P
Stator Diamter:14mm
Stator Length:4mm
Shaft Diameter: Φ1.5mm
Motor Dimension(Dia.*Len):Φ15mm*15mm
Weight:9g

Propellers

Propeller Diameter: 3.5 inch       
Pitch : 2              
Blades : 3
Material : Poly Carbonate        
Weight : 1.5g
Hub Diameter : 10mm           
Hub Thickness:4.7mm           
Shaft :1.9/1.5/1.9mm
Adaptor Rings : NO

Flight controller

(ELRS Version)

MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM42688P or BMI270 (SPI Control)
Mount pattern: 25.5×25.5 M2
Size:32*32*5mm
Power supply: 2-4S Lipo battery
Built-in 20A Blheli_s ESC each
Built-in Betaflight OSD(SPI Control)
Built-in UART ExpressLRS 2.4GHz receiver
Built-in 5V 1.5A BEC
Flight controller firmware target: CRAZYBEEF4DX

Flight controller

(Frsky version)

Model: CrazybeeF411 FRSKY

MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: BMI270 or ICM42688P(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 2-4S battery input (DC 8V-17V)
Built-in 20A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Frsky D8/D16 SPI receiverBuilt-in 2.4G Power Amplification
Built-in Betaflight OSD(SPI Control)
Built-in Current meter
Built-in 5V 1.5A BEC
Built-in voltage detectionFirmware target: MATEKF411RX

Onboard 4in1 ESC

MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV

Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT300

Onboard UART ExpressLRS 2.4GHz Receiver

(ELRS 2.4G Receiver version)

Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna plug: IPEX
Telemetry output Power: <12dBm
Receiver protocol:  CRSF
Default firmware version: ExpressLRS V3.0.1

Onboard SPI Frsky 2.4GHz receiver ( SPI Frsky Receiver Version)

SPI BUS receiver
Frsky D8/D16/EU-LBT/, Futaba S-FHSS switchable on Betaflight  
Channels: 8ch/16ch

Dual antenna
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 400m

Caddx FPV Digital HD Camera Nebula Nano Kit

(Digital HD version)

Weight(camera included]: 24g

Antenna: 2.3g

Dimensions: Vista Kit 30×29×13mm

                     Camera 14×14×21mm

Operating Frequency: 5.725-5.850GHz

Transmitter Power[EIRP]: FCC/SRRC/MIC:<30dBm

                                         CE:<14dBm

Min.latencylend-to-end) 720p 60fps:32ms

Max.Transmission Distance FcC/SRRC: 4km

CE:0.7km

lnput Power: 7.4-26.4V

Power Output: 25mW/200mW/500mW/700mw

Goggles : Work with DJl goggles

Camera Sensor: 1/3”CMOS

Lens: 2.1mm,f/2.1

Shutter: Rolling

shutterFOV: 142°(D);122°(H);75°(V)

LHCP antenna

Caddx ANT 1200tvl camera

(Analog version)

Image Sensor: 1/3′ CMOS Sensor

Horizontal Resolution: 1200 TVL

TV System: NTSC or PAL 

IMAGE: 16:9 or 4:3

Synchronization: Internal

Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000

S/N Ratio : >52dB (AGC OFF)

Video Output: CVBS

Lens: 1.8mm

Min. Illumination: 0.001Lux@F1.2

Auto Gain Control: YES

BLC: YES

WDR: Global WDR

DNR: 3D DNR

Dimensions: 14*14mm(with bracket to 19*19mm)

Wide Power Input: DC 3.7-18V

Work Temperature: -20℃~+60℃

Weight: 2g (N.W.)

OVX303 5.8Ghz VTX

(Analog version)

Model: OVX303

Frequency: 5.8G 40CH

Transmitting Power: 0/RCE/25mw/100mw/300mw

Power supply: DC 5V

Current (5v): <650ma (300mw)

Weight: 1.5gram without antenna

Antenna: RHCP